Custom Sizing: How to Specify Sheet and Platen Size

Read More Below

Have A Question About Vacuum Forming Machines?

We have been a manufacturer of thermoforming machines for more than thirty years. Whether you need large format vacuum forming machines to produce hot tubs or commercial signage or a smaller vacuum forming machine for mass produced product (like food packaging or medical packaging, our engineers are available to help you choose the right size and can provide tips on how to get a flawless finish.
We manufacture vacuum forming machines for a variety of use cases. Explore Our Products

Specifying a Custom Size Machine Starts With the Largest Part, Not the Sheet

A custom size vacuum forming machine is sized from the part outward. The sheet must be larger than the part, the platen must carry the mold, and the frame must clamp the sheet all the way around. If you start with a sheet size from a catalog and fit the part into it, you risk buying a machine that cannot make your next part.

Belovac builds each machine to order, and the custom large format vacuum forming machines page lists the configuration options. This article explains how to gather the numbers before that conversation. It belongs to the large format machine buyer’s guide.


Which Dimensions Define a Machine Size?

Four numbers set the size. Share all four with the builder rather than a sheet size alone.

  • Part footprint: the length and width of the largest part at the mold.
  • Draw depth: how far the part stands off the mold base.
  • Sheet blank: the starting sheet, which must exceed the footprint by the clamping margin and the material the draw consumes.
  • Mold size and weight: the platen must hold the tool, and the tool must also fit through the loading path.

The relationship between depth and sheet use is covered in how much sheet a deeper draw consumes, and depth limits are covered in the deep draw guide.


How Much Larger Than the Part Should the Sheet Be?

The sheet needs room for the clamp, for the material pulled into the draw, and for trim allowance. A shallow part on a flat mold needs little extra. A deep part on a large mold needs much more, because the sheet stretches over more surface than its footprint suggests. The thermoforming process thins the sheet as it stretches, so planning for the starting thickness and the final wall together avoids surprises.

Ask the builder to confirm the clamp margin on the frame you are considering, since it differs between designs.


What Does Sheet Thickness Do to the Specification?

Thick sheet needs more heat and more clamping force, and the specification should reflect the thickest material you expect to run. Belovac’s large format machines are listed for sheet from 0.020 to 0.250 inches, with a lower heater panel option for thicker gauge. If your plan includes thicker material, say so at the start, because it affects oven configuration as well as frame size.

Heating also scales with area. A bigger sheet needs enough heater zones to heat evenly across its width.


Should You Size for Today’s Part or Next Year’s?

Size for the largest part you realistically expect to form during the machine’s working life, within budget. A machine slightly oversized for current work gives room for new products. A machine sized exactly to today’s part can force an early replacement.

The table below shows how to weigh that choice.

Approach Advantage Risk
Size to current largest part Lowest cost and smallest footprint New products may not fit
Size with growth margin Room for larger or deeper parts Higher cost and floor space
Size to the product roadmap Fits planned products Depends on the roadmap holding

What Else Should Be Checked Before Locking the Size?

A bigger machine needs a building that can take it. Check floor load, door and crane access, and clearance around the frame before the size is final. The article on facility readiness for a large format machine lists what to confirm, and the large format machine category page shows the range of applications Belovac builds for.


Belovac: Start With Your Part Drawing

The fastest route to a correct size is a drawing of your largest part. Request a quote and we’ll help you specify the sheet and platen size for your part.

Have A Question About Vacuum Forming Machines?

We have been a manufacturer of thermoforming machines for more than thirty years. Whether you need large format vacuum forming machines to produce hot tubs or commercial signage or a smaller vacuum forming machine for mass produced product (like food packaging or medical packaging, our engineers are available to help you choose the right size and can provide tips on how to get a flawless finish.

Featured Video

Have A Question About Vacuum Forming Machines?

Scroll to Top